DSC Power832 Security System PC5016 Specifikace stáhnout pdf (Strana 15)

K E Y P A D C O M M A N D S

How to program Access Code Attributes:

“Master Code” attributes cannot change. By default, each code has the attributes of the code

used to program it.

1.Enter [ ][5][Master Code]. The keypad will flash the ‘Program’ light and turn on the zone light for any

code already programmed.

2.Press [9] to enter the Attribute mode. The keypad will turn on the ‘Ready’ light and turn off the armed light.

3.Enter the 2 digit number for the code you want to program Attributes for. Zone lights [1] to [4] will be on

or off. Refer to the following chart:

Zone Light 1 - ON - enable code for Partition 1

Zone Light 2 - ON - enable code for Partition 2

Zone Light 3 - ON - enable Zone Bypass

4.Enter [1] to [3] to turn the zone lights ON or OFF, then press [#] key.

5.Continue with steps 2 and 3 until all code attributes are programmed.

After all the codes and attributes have been programmed press the [#] key to exit Access Code

Programming.

How to erase Access Code:

Select the code to be erased and press [

[

]+[6] User Functions

This keypad command can be used to program several different functions. The following are the items

programmable:

[1] - Time and Date

[2] - Auto-Arm Enable *

[3] - Auto-Arm Time *

[4] - System Test

[5] - Enable DLS (Downloading)

[6] - For future use

[7] - Enable background music

Auto-Arm items (noted with the “*” symbol) are programmable by Partition. These must be programmed at

a keypad assigned to the correct Partition

(See Section 2.6 “Keypad Assignment”).

To program User Functions:

1.Press [ ] [6] [Master Code]. The keypad will flash the ‘Program’ light.

2.Press the number [1] to [5] for the item to be programmed.

• [1] - Time and Date

The time and date must be accurate for the Auto-Arm or Test Transmission functions to work properly. In

addition the event buffer time and date stamps all events.

- Enter the time: hour and minute, using military format [HH MM]. (00:00 to 23:59)

- Enter the date: month, day and year [MM DD YY].

All entries must be 2 digits. January, for example, would be month [01].

• [2] - Auto-Arm Enable/Disable

Auto-Arming will not work until it is enabled for the Partition.

Press [2]. If the keypad beeps 3 times rapidly Auto-Arm is enabled, one long beep means it is disabled.

• [3] - Auto-Arm Time

Each Partition can be programmed to Auto-Arm at a different time.

Enter the time, hour and minute, using military format [HH MM].

All entries must be 2 digits. Eight o’clock in the morning would be [08] hours and [00] minutes.

• [4] - System Test

When [4] is pressed the panel will perform the following:

- sound the alarm output for two seconds

- light all lights on the keypad

- sound the keypad buzzer for two seconds

- test the main panel/PC5204 battery

- send a System Test Reporting code, if programmed

(See Section 5.7 “Communicator - Reporting Codes”)

• [5] - Enable DLS (Downloading)

When [5] is pressed the panel will turn on the downloading option for 6 hours. During this time the panel

will answer incoming downloading calls

(See Section 5.8 “Downloading”)

• [6] - For future use

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 43 44

Komentáře k této Příručce

Žádné komentáře

DSC Power832 Security System PC5016 Specifikace Strana 15

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC Power832 Security System PC5016