DSC PC255O Specifikace stáhnout pdf (Strana 11)

This output can be used for operating other devices such

as garage door opener, special lighting or door strikes.

The programmable output must be selected for keypad

utility using the [✱][8][Installer’s Code][30] command and

programming a [2], [3], [4] or [5].

Depending on the option chosen in the programming

section, the programmable output is activated by

pressing the [✱] then [7] keys followed by a Group A

access code, Group B access code, any access code, or

no code at all. When the proper keys are pressed the

keypad sounder and the programmable output are

activated for 5 seconds.

Installer’s Programming Commands

[✱]+[8]+[INSTALLER’S CODE]

The PC2550 is completely programmed from the keypad

by using commands in the [✱] [8] section. The

commands are described in detail in the programming

section of this manual.

“At Home” Arming

[✱]+[9]+[ACCESS CODE]

Entering [✱], [9] before the arming code, arms the panel

without any entry delay on the delay zones and bypasses

zones that are defined as “Home-Away”. This command

is used for arming the system while at home. When the

panel is armed using [✱], [9], the “Armed” light will be on

flashing and the bypass light will be on to indicate that

the “Home-Away” zones are bypassed. Once the panel is

armed in this mode, using [✱], [1] will remove the bypass

from those zones defined as “Home-Away” if they have

NOT

been manually bypassed. The [✱], [1] command

used here, only removes the bypass from zones that have

been Automatically bypassed with the [✱], [9]

command.”

“Quick Arm” Command

[✱]+[0]

Entering [✱][0] is accepted as a valid arming code when

the “Quick Arm” feature is activated. This command is

often used when individuals are required to arm the

system. These individuals will not be able to disarm the

system. This could be used with home visitors in the case

of a residential alarm or junior employees and

maintenance staff in the case of a commercial alarm.

See instructions in the “[✱][6] User’s Functions

Command” section for activating the “Quick Arm” feature.

This feature should not be enabled if the One Time Use

Code is enabled. The One Time Use Code must be used

for arming before it is erased.

Quick Exit

[✱]+[0] When Armed

Entering [✱] [0] when the system is fully armed will allow

the user 2 minutes to exit the premises through any delay

zone without altering the status of the system if the Quick

Exit feature is enabled. The Quick Exit feature can be

enabled by turning on light 1 in section [18]. After [✱] [0]

is entered into an armed system, one and only one delay

zone may be tripped. Any additional activity on any other

active zone will cause that zone to begin its alarm

sequence.

[✱] [0] for Quick Exit on a partially armed system is not

supported.

Quick Exit must not be used when auxiliary delay zones

are force armed. Turn light 6 in section [17] off to ensure

proper operation.

Note: Quick exit shall not be enabled on UL listed

systems.

Keypad Zones

There are three zones which can be activated from the

keypad. The alarm and restoral codes for keypad zones

are programmed using the [✱][8] command.

Pressing the [F] key or the [1] and [3] keys for 2 seconds

activates a Fire alarm. The fire alarm sounds the siren/bell

in a pulsed mode and is annunciated as a memory

condition. The Fire key can be turned off in section [18].

Pressing the [A] key or the [4] and [6] keys for 2 seconds

activates an Auxiliary keypad zone. If a reporting attempt

is made to an alarm receiver and it is successful the

PC2550 will acknowledge the transmission with a short

series of beeps from the keypad.

Pressing the [P] key or the [✱] and [#] keys for 2 seconds

activates the Police (or Panic) alarm. The panic alarm can

be programmed for audible or silent operation (see

sections [15] and [18] in “Programming Guide”).

There is no light annunciation from the keypad for the last

two keypad zones, however, the keypad buzzer beeps 3

times to confirm activation on any of the keypad zones.

See section [11] for alarm and restoral codes for all three

keypad zones.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Komentáře k této Příručce

Žádné komentáře

DSC PC255O Specifikace Strana 11

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC PC255O