DSC PC255O Specifikace stáhnout pdf (Strana 10)

automatically extended to include the day (two digits

01.....31), the month (two digits 01.....12) and the year

(two digits...e.g. 91, 92, 93....etc.).

Installer’s Test

[✱]+[6]+[MASTER CODE]+[0]

This feature is designed to assist the installer in testing

the system. In this mode, the bell or siren will operate for

two seconds each time a device is tripped and the first

level of memory will be affected. The feature is

automatically disabled when the panel is armed and

disarmed. Each time a zone is tripped or restored in this

mode, a signal, if programmed, will be transmitted to the

monitoring station. If this is not desired, it is possible to

disable the communicator during the test (see section

[15] “1st System Option Code”). A printer, if attached,

will not function if the communicator is disabled.

Notes: Do not use the PC16OUT module during the

installer’s test.

Do not use the installer’s test when the panel is

partially armed.

Setting the Clock

[✱]+[6]+[MASTER CODE]+[1]

Setting the “System 24 Hour Clock” (item [1]) tells the

system the correct time of day. If the system is without

battery and AC power it cannot continue to keep time.

Therefore when the panel is first powered up or when it

has been without AC power long enough to completely

discharge the stand-by battery, the “System 24 Hour

Clock” must be reset. If the time needs to be reset a

“Trouble #8” will be indicated on the keypad (see [✱][2]

“System Trouble Command”). If a printer is attached to

the panel, setting the clock must include the day, month

and year. e.g. HH: MM: DAY: MONTH: YEAR.

Auto-arm Time of Day

[✱]+[6]+[MASTER CODE]+[2]

Note: Auto-arm cannot be used for UL installations.

The PC2550 can be programmed to arm at the same time

each day. Programming item [2] sets this time and the

feature must be enabled as shown in item [5] (see “Auto-

arm Enable” on this page).

At the selected auto-arm time the keypad beeper begins

to sound and the Bell/Siren will pulse once every 10

seconds to alert anyone on the premises that the system

is about to arm. The Bell/Siren pulse can be silenced in

section [17] by turning light 1 on.

The keypad beeper will sound for one minute before auto-

arming unless one of the following two methods is used to

abort the auto-arm.

• Auto-arm abort: Any key can be pressed to abort the

auto-arm sequence and silence the keypad during the

one minute pre-alert (this is the default condition).

• Auto-arm abort with code: If section [17] light 4 is on,

then a valid 4 digit access code is required to abort the

auto-arm sequence.

The auto-arm will be attempted at the same time the

following day. Any time an auto-arm is aborted using one

of the above methods, the reporting code programmed in

section [08] will be transmitted to the central station.

When the panel does arm by auto-arming, any open

zones will be “Force-armed”. If light 5 in section [18] is

on, the panel will send a partial closing code to let the

central station know zones were bypassed. If section [16]

light 1 is on, the zones that were force-armed will be

identified by transmitting their alarm code along with the

partial closing code.

Quick Arm

[✱]+[6]+[MASTER CODE]+[4]

The “Quick Arm” feature is enabled by pressing the [4]

key while in the “User Functions Command” section.

When enabled (enabled 3 beeps....disabled one long

beep) the panel can be armed by entering [✱][0]. The

closing code transmitted for “Quick Arm” is the same as

the code which is programmed for the Master Code.

Auto-arm Enable

[✱]+[6]+[MASTER CODE]+[5]

Entering [✱] [6] [Master Code] [5] will enable/disable the

auto-arming feature. When the feature is being enabled,

the keypad buzzer will sound 3 beeps and when being

disabled the buzzer will sound one long beep.

Note: Auto Arm must be disabled on UL Listed

systems.

Door Chime

[✱]+[6]+[MASTER CODE]+[6]

The “Door Chime” feature is enabled by pressing the [6]

key while in the “User’s Functions Command” section.

When enabled the keypad buzzer will beep quickly 5

times each time any zone defined as a delay or instant

circuit opens or closes. The “Door Chime” feature does

not operate on other zone definitions. Zone bypass may

be used to eliminate “beeping” on doors where it is not

wanted. This feature operates only while the panel is

disarmed.

System Test

[✱]+[6]+[MASTER CODE]+[8]

The system test feature sounds the bell or siren, lights the

keypad indicators and beeps the keypad buzzer for 2

seconds. If a code is programmed in section [50] it will

be transmitted at the same time.

User Callup

[✱]+[6]+[MASTER CODE]+[9]

This function is enabled in section [47]. When activated,

the panel will call the downloading computer. The

downloading computer must be waiting for the panel to

call before downloading can be performed.

Utility Output Command

[✱]+[7] OR [✱]+[7]+[ACCESS CODE]

The programmable output (PGM terminal) on the PC2550

can be made to activate by a command from the keypad.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 43 44

Komentáře k této Příručce

Žádné komentáře

DSC PC255O Specifikace Strana 10

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC PC255O