DSC Power832 PC5O15 Instalační manuál stáhnout pdf (Strana 13)

G E T T I N G S T A R T E D

2.9 Removing Modules

If a module is no longer required on the system the panel must be told to no longer supervise the module. To do this

remove the module from the Keybus and perform the Enable supervision function again (

See Section 2.7 “Enable

Supervision”).

The panel will see the module has been removed and will no longer supervise it.

2.10 Zone Wiring

For a complete description of the operation of all zone types, please refer to Section 5.1 (“Zone Definitions”).

There are several different ways in which zones may be wired, depending on which programming options have been

selected. The panel can be programmed to supervise normally closed, End of Line, or Double End of Line loops.

Please refer to the following sections to study each type of individually supervised zone wiring.

Any zone prAny zone pr

Any zone pr

ogrammed for Firogrammed for Fir

ogrammed for Fir

e or 24 Hour Supere or 24 Hour Super

e or 24 Hour Super

visorvisor

visor

y must be wiry must be wir

y must be wir

ed with a single End of Line (EOL)ed with a single End of Line (EOL)

ed with a single End of Line (EOL)

esistor resistor r

esistor r

egaregar

egar

dless of the type of zone wiring superdless of the type of zone wiring super

dless of the type of zone wiring super

vision selected for the panel (section [013], optionsvision selected for the panel (section [013], options

vision selected for the panel (section [013], options

[1] and [2]). See Section 5.1 “Zone Definitions.”[1] and [2]). See Section 5.1 “Zone Definitions.”

[1] and [2]). See Section 5.1 “Zone Definitions.”

If you change the zone superIf you change the zone super

If you change the zone super

vision options frvision options fr

vision options fr

om DEOL to EOL or from DEOL to EOL or fr

om DEOL to EOL or fr

om NC to DEOL (section [013],om NC to DEOL (section [013],

om NC to DEOL (section [013],

options [1] or [2]), you should power down the system completelyoptions [1] or [2]), you should power down the system completely

options [1] or [2]), you should power down the system completely

, and then power it back up. If you, and then power it back up. If you

, and then power it back up. If you

do not, the zones may not work cordo not, the zones may not work cor

do not, the zones may not work cor

ectlyectly

ectly

2.10.1 Normally Closed (NC) Loops

2 NORMALLY CLOSED

CONTACTS WITH

NO END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

NORMALLY CLOSED

CONTACT;

NO END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

To enable normally closed loops, programming section [013], option [1] must be ON.

This option should only be selected if NorThis option should only be selected if Nor

This option should only be selected if Nor

mally Closed (NC) devices/contacts armally Closed (NC) devices/contacts ar

mally Closed (NC) devices/contacts ar

e being usede being used

e being used

Normally Closed Loops .......................................... Section [013], Option [1]

2.10.2 Single End Of Line (EOL) Resistors

NORMALLY CLOSED

CONTACT WITH

5600 Ω END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

NORMALLY OPEN

CONTACTS WITH

5600 Ω END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

ANY Z

TERMINAL

ANY COM

TERMINAL

2 NORMALLY OPEN

CONTACT AND

2 NORMALLY CLOSED

CONTACT WITH

5600 Ω END OF LINE

RESISTOR

1 NORMALLY OPEN

CONTACT AND

1 NORMALLY CLOSED

CONTACT WITH

5600 Ω END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

To enable panel detection of single end of line resistors, programming section [013], options [1] and [2] must be

OFF.

This option should be selected if either NorThis option should be selected if either Nor

This option should be selected if either Nor

mally Closed (NC) or Normally Closed (NC) or Nor

mally Closed (NC) or Nor

mally Open (NO) detectionmally Open (NO) detection

mally Open (NO) detection

devices or contacts ardevices or contacts ar

devices or contacts ar

e being usede being used

e being used

End of Line Resistors ............................................. Section [013], Option [1]

Single End of Line Resistors .................................. Section [013], Option [2]

2.10.3 Double End of Line (DEOL) Resistors

Double End of Line resistors allow the panel to determine if the zone is in alarm, tampered or faulted.

To enable panel detection of double end of line resistors, programming section [013], option [1] must be OFF

and option [2] must be ON.

ANY Z

TERMINAL

ANY COM

TERMINAL

ALARM

CONTACT

DOUBLE EOL CIRCUIT

1 NORMALLY CLOSED

CONTACT WITH

5600Ω END OF LINE

RESISTORS

If the Double EOL superIf the Double EOL super

If the Double EOL super

vision option is enabled, all harvision option is enabled, all har

vision option is enabled, all har

dwirdwir

dwir

e zones must be wire zones must be wir

e zones must be wir

eded

for Double EOL rfor Double EOL r

for Double EOL r

esistors, except for Firesistors, except for Fir

esistors, except for Fir

e and 24 Hour Supere and 24 Hour Super

e and 24 Hour Super

visorvisor

visor

y zones.y zones.

y zones.

o not wiro not wir

o not wir

e DEOL re DEOL r

e DEOL r

esistors on keypad zones.esistors on keypad zones.

esistors on keypad zones.

o not use DEOL ro not use DEOL r

o not use DEOL r

esistors for Firesistors for Fir

esistors for Fir

e zones or 24 Hour Supere zones or 24 Hour Super

e zones or 24 Hour Super

visorvisor

visor

y zones. Do not wiry zones. Do not wir

y zones. Do not wir

FirFir

Fir

e zones to keypad zone tere zones to keypad zone ter

e zones to keypad zone ter

minals if the DEOL superminals if the DEOL super

minals if the DEOL super

vision option is selected.vision option is selected.

vision option is selected.

his option can only be selected if Norhis option can only be selected if Nor

his option can only be selected if Nor

mally Closed (NC) detection devices ormally Closed (NC) detection devices or

mally Closed (NC) detection devices or

contacts arcontacts ar

contacts ar

e being used. Only one NC contact can be connected to each zone.e being used. Only one NC contact can be connected to each zone.

e being used. Only one NC contact can be connected to each zone.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 47 48

Komentáře k této Příručce

Žádné komentáře

DSC Power832 PC5O15 Instalační manuál Strana 13

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC Power832 PC5O15