Power Supply/Output Expansion
PC5200 Power Supply Module
• The PC5200 can be used to provide up to 1.0A of additional power to
the Power632 security system
• Fully supervised for tamper, low battery, AC power loss, and auxiliary
power loss
• Connect up to 1000’ (305m) from the control panel via Keybus
• Specifications
- auxiliary current: 1.0A continuous rating; 3.0A short term if backup
battery connected (PTC-protected – fuseless design)
- transformer requirements: 16.5V, 40VA
- battery requirements: 4Ah
- Current draw: 20 mA
PC5204 Power Supply/High Current Output Module
• Provides 1A @ 12.5Vdc auxiliary power for additional modules and
devices
• Includes 4 fully programmable high current outputs
- rated at 1A @ 12Vdc, PTC protected
- will provide 3A short term if battery backup connected
- each output can sink up to 3A
• Output #1 may also be used as a supervised bell output
- 700mA max
• Each output programmable to activate for any of 24 options
• Connect up to 1000' (305m) from control panel via KEYBUS
• Fully supervised for: tamper, low battery, AC power loss, and
auxiliary power trouble
• Maximum 1 module per system
• Battery required : 4Ah minimum
• Transformer required : 16.5Vac, 40VA
• Module current draw: 20mA @ 12VDC
PC5208 Low Current Output Module
• Module provides 8 low current transistor switch outputs
- each output can sink up to 50mA
- up to 250mA max at one time
• Each output programmable to activate for any of 24 options
• Connect up to 1000' (305m) from control panel via KEYBUS
• Fully supervised for tamper
• Maximum 1 module per system
• Specifications
- Current draw: 20mA @ 12VDC
PC5320 Multiple Wireless Receiver Module
• Up to 4 wireless receivers can be installed on the system via this
module, providing multiple transmission paths, and significantly
increasing the coverage area for wireless products
• Specifications
- Current draw: 55 mA (maximum)
Integrated Voice Assisted Security
& Automation
ESCORT5580TC Voice Assisted Security &
Automation Control Module
• Turns any touch-tone phone into a fully functional keypad with
Global and Partition control
• Built-in power line interface for control of 32 X-10 automation
control devices
- 16 schedules with On Time, Off Time, and Day of Week
- 8 user controlled automation modes
- full range of dimming levels for lighting control
- event activated control for any PGM output supported by the
main panel
• An extensive library of voice prompts for security and
automation operation, programming, and system status
feedback
- 250 system words for pre-programmed system functions
- 240 word library for user programmable voice prompts for
Automation Item Labels, Automation Mode Labels, Partition
Labels, and Zone Labels
• Program up to 6 words per voice label
• Powerful ‘say number’ command can announce numbers from
0-999 in three different ways
• Supports up to four EMS-100 thermostats
• EMS-100 has 4 temperature control modes :
- day occupancy mode
- night occupancy mode
- auxiliary occupancy mode
- away occupancy mode
• Each thermostat optionally supports:
- up to six EMS-IDS remote indoor temperature sensors for
interior temperature averaging
- one EMS-ODS outdoor temperature sensor for display of
outdoor temperature
• Connect up to 1000' (305m) from control panel via KEYBUS
• Specifications
- Current draw: 150mA @ 12VDC
(28 stránky)
(12 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce