DSC NT9005 V1.0 Specifikace stáhnout pdf (Strana 13)

[702] Second International Option Codes

OFF Land line Test Transmission is in Days !

The value programmed in section [370] option 7 is in days.

4 ON 1600 Hz Handshake 

The communicator responds to a 1600Hz handshake for

bps formats.

OFF Standard Handshake !

The communicator responds to the handshake desig-

nated by the format selected in section [360].

5 ON I.D. Tone Enabled 

After the telephone number is dialed, the system emits

the tone programmed in option 6.

OFF I.D. Tone Disabled !

6 ON I.D. Tone Frequency = 2100 Hz 

This tone is enabled in option 5.

OFF I.D. Tone Frequency = 1300 Hz !

This tone is enabled in option 5.

7 ON 1-Time/1-Hour DLS Window enabled 

Allows the user to initiate a DLS downloading session.

OFF 6-Hour DLS Window enabled !

8 ON Bell on FTC when Armed 

If a failure to communicate trouble is generated while the

system is armed, the bell output will sound for the time pro-

grammed in section [005] or until the system is disarmed.

OFF FTC Trouble only when Armed. !

If a failure to communicate trouble is generated while the

system is armed, the bell output will not sound but the key-

pad buzzer will sound trouble beeps until a key is pressed.

[703] Delay between Dialing Attempts

For standard (force) dialing the system will search for a dialtone

for 5 seconds, hang up for 20 seconds, search for a dial tone for

5 seconds then dial. If there is no initial handshake recognized

within 40 seconds, the system will hang up. This timer adds a

delay before the next call is attempted. The default is one sec-

ond (001) delay for a total of six seconds.

Default 001 I___I___I___I 000 - 255 second

2-3 System Wiring

the wall. Slide tabs on bottom of unit into the

slots of the back cover.

4. Secure unit in place with the two screws pro-

vided.

2-3 System Wiring

The R, B, Y1, G2 terminals located on the inside of

the back cover, can be configured as a Keybus, or 2

hardwired zones or 2 PGMs (programmable out-

puts), or 1 PGM and 1 hardwired zone . If config-

ured as a Keybus or hardwired zone, wire devices

using 22 AWG stranded wire; maximum wire run

distance must not exceed 1000 ft. (305 m.).

2-3.1 Keybus Wiring

The Keybus is used to communicate to other mod-

ules on the system. In this configuration the ‘R’ ter-

minal is +6V

, the B terminal is ground, Y1

terminal is the CLOCK and the G2 terminal is the

DATA. If the system is configured for Keybus then

Keybus Enabled (section [018] option 1) must be

ON. Hardwired zones 1 and 2, and PGMs 1 and 2

will not be available. If an NT9204 module is con-

nected to the system (via the Keybus) then PGMs

11, 12, 13 and 14 will be available. Enter [00] in

section [030] when an NT9204 is used.

☞

The Keybus can not drive any module other

than the NT9204 directly. To connect to Sky-

route®, an NT9204 module must be con-

nected to the Keybus.

2-3.2 Programmable Output Wiring

Programmable outputs (PGMs) are available directly

from the system panel or from the NT9204 module.

When activated, the output will switch to ground.

PGM outputs can be programmed in any of the

options listed in section [009] and can be custom-

ized using up to 8 attributes, see section [141].

☞

PGMs 3 through 10 are not supported at this

time.

PGMs 1, 2 - PGM 1 and 2 can sink 50 mA. This out-

put can drive an LED indicator or small buzzer

directly. Connect Y1 (PGM 1) or G2 (PGM 2) to the

negative (-) terminal of the device and connect the

positive terminal of the device to the R terminal. If

current greater than 50 mA, or voltage greater than

6 V

is required for an application then a relay

must be used.

Example of Keybus Wiring

Module A is wired correctly

(within 1000’/305m of the panel)

Module B is wired correctly

(within 1000’/305m of the panel)

Module C is NOT wired correctly

(greater than 1000’/305m from the

panel)

* Not used for UL Installations

Use an external source for power that is UL Listed

to UL1481 for Fire and UL603 for Burglary.

** Model

PTD920T-ANZ

GRN YEL BLK RED AC AC

UA440

GRN YEL BLK RED AC AC

UA440

Jumper J10 must

be in place for

tamper to work

Tamper

Switch

Backup

Battery

Figure 5

WWW.DIYALARMFORUM.COM

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 29 30

WWW.DIYALARMFORUM.COM 1

Komentáře k této Příručce

Žádné komentáře

DSC NT9005 V1.0 Specifikace Strana 13

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC NT9005 V1.0