DSC WTK5504 Instalační manuál stáhnout pdf (Strana 6)

Installers Mode and selecting Diagnostics. Refer to

Appendix B for the List of Diagnostics. Once the

module(s) have been isolated a PC4204 will be required

to increase the power to be module with the low voltage

trouble. Now that all trouble have been taken care of the

next step is to remove AC power from all modules and

allow the panel to run for 10 - 15 minutes on battery power

alone. If there are any Combus Low Voltage troubles a

PC4204 Combus repower module may be required at the

Low voltage location to insure proper system operation.

Repeat this test as required.

Mounting the Panel

Select a dry location close to an unswitched AC source, a

ground connection and a telephone connection for

mounting the Main Control Cabinet.

Remove the PC4020 printed circuit board, mounting

hardware, and keypad from the cardboard retainer inside

the large cabinet. Before attaching the cabinet to the wall,

press the five white nylon printed circuit board mounting

studs into the cabinet from the back. Mark the mounting

holes on the wall. Drill the appropriate hole size and insert

wall plugs into the holes. Next, using #8x1" round headed

screws (or equivalent) secure the cabinet to the wall.

Pull all cables into the cabinet and prepare them for

connection before mounting the circuit board to the back

of the cabinet. Press the circuit board down onto the

mounting studs.The wiring must be fixed/routed so as to

prevent the telephone network wiring and all other wiring

from crossing each other.

NOTE: In order to comply with safety requirement

IEC950, ensure that when the mains cabling enters the

alarm panel, it is securely clamped to prevent it from

being removed.

Caution: If the neutral in the main supply is not readily

identifiable, then an appropriate disconnect device that

has a contact separation of at least 3mm and

disconnects both poles simultaneously, must be used.

There is room in the Main Control Cabinet (PC4001C) for

any two modules (PC4108, PC4116, PC4216 or PC4400).

Modules requiring power (AC and battery PC4204) must

be installed in the large Expander Cabinet (PC4002C).

This enclosure will accommodate one module (PC4108,

PC4116, PC4216 or PC4400) and a powered output

(PC4204) or any three modules. A small Expander Cabinet

(PC4003C) is available for a single module that does not

require external power.

Interconnection circuits should be such that the equipment

continues to comply with the requirements of IEC950 when

like circuits are connected to each other. For example, TNV

(telephone network) circuit should be connected to the

TNV circuit, SELV (zoned) circuits should be connected to

SELV.

Once the wiring is completed power the system up by first

connecting the battery followed by the AC transformer. All

LCD4500 keypads should display the message ‘LCD4500

DSC Ltd.’. Press a key on any keypad that is to be

assigned to Partition 1. The keypad will beep and display

the message ‘4500 Mod. #1' and the keypad is

automatically assigned to Partition 1.

Enroll every module to the system. Make sure you put

down the number of each module enrolled. Refer to the

Programming Manual for the required procedure.

When enrolling any PC4108 or PC4116 zone expander

module make sure to note the zones which you assigned

to the module.

This information is very important if it becomes necessary

to Add or Delete zones to or from a Partition. Zones 1

through 16 are assigned to Partition 1 by default. This can

be changed later in Installer Programming.

In Book 4 (Programming Work Sheets) you will find a

System Overview section. Fill in the information as each

module is enrolled. These sheets are designed to be left

in the panel so if future service is required, the location

and assigned number of each module will be readily

available.

Once all modules are enrolled perform a diagnostics

check on the panel to determine if any problems are

present (see “Diagnostics”).

Programming the System

The PC4020 has the capability to operate as 8 separate

alarm systems called Partitions. Dividing the panel into

Partitions will allow you to control access to specific areas.

When the PC4020 is first powered up all zones on the

main board and User Codes are assigned to Partition 1. If

no other Partitions are required the entire system will be

considered Partition 1. This is important to keep in mind

as often in programming the panel will require you to enter

the Partition to program.

For example, when programming entry and exit times, you

must select the menu option ‘ADD/EDIT PAR’. The keypad

will then prompt you for the Partition to add or edit. You

must select Partition 1 for a system that has no additional

Partitions.

The factory default setting for all options is provided in the

Programming Work Sheets as well as programming

‘HOTKEYS’ for the option to allow quick programming.

Complete the Programming Work Sheets located in Book

4. Having this information prepared before programming

the panel will speed up the process considerably.

All information for the panel may be entered in the

Programming Work Sheets.

Any zone expanders on the system will include a similar

sheet and the information should be completed for

these as well.

There is no set order in which the panel must be

programmed, however, if you use the following guideline it

may simplify the programming of the panel for the first time.

Step 1 - Define all Partitions

When the panel is first powered up the 16 zones on the

main panel are assigned to Partition 1. Additional zone

1 2 3 4 5 6 7 8 9 10 11 ... 35 36

Komentáře k této Příručce

Žádné komentáře

DSC WTK5504 Instalační manuál Strana 6

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC WTK5504