DSC Power8 PC5OO5 Instalační manuál stáhnout pdf (Strana 14)

G E T T I N G S T A R T E D

2.10.2 Single End Of Line (EOL) Resistors (5600

ΩΩ

Ω)

NORMALLY CLOSED

CONTACT WITH

5600 Ω END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

NORMALLY OPEN

CONTACTS WITH

5600 Ω END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

ANY Z

TERMINAL

ANY COM

TERMINAL

2 NORMALLY OPEN

CONTACT AND

2 NORMALLY CLOSED

CONTACT WITH

5600 Ω END OF LINE

RESISTOR

1 NORMALLY OPEN

CONTACT AND

1 NORMALLY CLOSED

CONTACT WITH

5600 Ω END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

To enable panel detection of single end

of line resistors, programming section

[013], options [1] and [2] must be OFF.

This option should be selected

if either Normally Closed (NC)

or Normally Open (NO)

detection devices or contacts

are being used

End of Line Resistors ............................................. Section [013], Option [1]

Single End of Line Resistors ................................. Section [013], Option [2]

2.10.3 Double End of Line (DEOL) Resistors

Double End of Line resistors allow the panel to determine if the zone is in alarm, tampered or faulted.

To enable panel detection of double end of line resistors, programming section [013], option [1] must be OFF and

option [2] must be ON.

ANY Z

TERMINAL

ANY COM

TERMINAL

ALARM

CONTACT

DOUBLE EOL CIRCUIT

1 NORMALLY CLOSED

CONTACT WITH

5600Ω END OF LINE

RESISTORS

If the Double EOL supervision option is enabled, all hardwire zones must be wired

for Double EOL resistors, except for Fire and 24 Hour Supervisory zones.

Do not wire DEOL resistors on keypad zones.

Do not use DEOL resistors for Fire zones or 24 Hour Supervisory zones. Do not wire

Fire zones to keypad zone terminals if the DEOL supervision option is selected.

This option can only be selected if Normally Closed (NC) detection devices or

contacts are being used.

Only one NC contact can be connected to each zone. Wiring multiple detection

devices or contacts on a single loop is not allowed

The following chart shows zone status under certain conditions:

Loop Resistance Loop Status

0Ω (shorted wire, loop shorted) Fault

5600Ω (contact closed) Secure

Infinite (broken wire, loop open) Tamper

11200Ω (contact open) Violated

End-of-Line Resistors ............................................ Section [013], Option [1]

Double End-of-Line Resistors ............................... Section [013], Option [2]

2.10.4 Fire Zone Wiring - 4 wire Smoke Detectors

All zones defined as Fire

(See Section 5.1 “Zone Definitions”)

must be wired according to the following diagram:

For a complete description of how fire zones operate,

see Section 5.1 “Zone Definitions”.

2.10.5 Fire Zone Wiring - 2 wire Smoke Detectors

If PGM2 has been programmed for 2 Wire Smoke Detector connection

(See Section 5.10 “PGM Output”),

the

detectors must be wired according to the following diagram:

Ω

For a complete description of how fire zones operate,

see Section 5.1

“Zone Definitions”.

If PGM2 is programmed for 2 wire smoke support, Jumper CON1

on the main board must be removed.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 45 46

Komentáře k této Příručce

Žádné komentáře

DSC Power8 PC5OO5 Instalační manuál Strana 14

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC Power8 PC5OO5