DSC Power432 PC585 Instalační manuál stáhnout pdf (Strana 30)

When used as a backup communicator, the panel will attempt

to call the central station in the following manner:

the panel will try to call using land lines – if unsuccessful, the

panel will try to call using the LINKS – if unsuccessful, the

panel will try to call using the land lines on the next dialing

attempt. This process will continue until the panel has suc-

cessfully communicated with the central station or until the

panel’s programmed number of dialing attempts have been

exhausted.

Using the LINKS as a Redundant Communicator

The panel can be programmed to call using first the

LINKS1000 and then the land line when an event occurs. To

program this option, select both the telephone number and

the LINKS options for the Communicator Call Direction

Options for the event. The Call LINKS as well as Land Line

option must be selected.

LINKS Special Preamble

In some areas of North America, dialing #DAT or *DATA

reduces the cellular billing increment. The LINKS Special

Preamble (section [393]), allows the use of [*] and [#] charac-

ters for the programming of #DAT and *DATA.

The LINKS Special Preamble is sent BEFORE the Preamble

programmed in Sections [390] to [392].

Example: [Special Preamble][Regular Preamble][Telephone

Number]

NOTE: If this Special Preamble is programmed, it will be

inserted before the Regular Preamble of ALL telephone num-

bers. Hex digits D and E are not supported for Preamble pro-

gramming.

NOTE: If Busy Tone Detection is enabled, the LINKS1000

must be tested to ensure full operation.

Please refer to the LINKS1000 installation Manual for more

information and connection diagrams.

LINKS Preamble (First Telephone Number) . . . Section [390]

LINKS Preamble (Second Telephone Number). Section [391]

LINKS Preamble (Third Telephone Number) . . . Section [392]

LINKS Preamble

(Downloading Telephone Number) . . . . . . . . . . Section [490]

Communicator Call Direction Options. . . Section [361]-[368]

Call LINKS as well as Land Line . . . . . . . . . Section [380]: [7]

LINKS Special Preamble . . . . . . . . . . . . . . . . . . Section [393]

5.27 Additional System Modules

The following modules are programmed through the module

programming sections [801]-[804]: the PC5400 Printer mod-

ule, the Links2X50 Long-Range Radio module, and the

PC5132 Wireless Receiver and all of its devices. For instruc-

tions on the installation and programming of these additional

modules and devices, please see their respective installation

and programming manuals.

PC5400 Printer Module Programming. . . . . . . . Section [801]

Alternative Comm. (LINKS2X50)

Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . Section [803]

PC5132 Programming . . . . . . . . . . . . . . . . . . . . Section [804]

5.28 Clock Adjust

In order to compensate for timing inaccuracies, the panel may

be programmed to add or subtract seconds during the last

minute of each day using the Clock Adjust programming sec-

tion. Valid entries are 01 - 99. The default setting is 60 sec-

onds. To determine the value to be programmed in this

section, monitor the amount of time lost or gained by the panel

over a period of time. Then, calculate the average amount of

time per day that the panel gains or loses. If the clock’s timing

is off, it may be corrected with this setting.

Example #1: The clock loses an average of 9 seconds per

day.

Solution: Program the panel to adjust the clock by 51 sec-

onds (instead of the default 60 seconds) for the last minute of

each day in section [700]. This will speed up the panel’s clock

by 9 seconds, correcting the problem.

Example #2: The clock gains an average of 11 seconds per

day.

Solution: Program the panel to adjust the clock by 71 sec-

onds (instead of the default 60 seconds) for the last minute of

each day in section [700]. This will slow down the panel’s

clock by 11 seconds, correcting the problem.

NOTE: If the Auto-arm time is set for 23:59, any change to the

Clock Adjust option will directly affect the Auto-arm pre-alert

time.

Clock Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [700]

5.29 Timebase

In cases of unstable AC power input you can use the internal

crystal to keep a more accurate timebase by enabling the

Timebase is Internal Crystal option.

If the 50 or 60Hz AC power input is very stable it can be used

as the timebase, by enabling the Timebase is AC line option.

Timebase Internal Crystal/AC line . . . . . . . Section [701]: [2]

5.30 Resetting Factory Defaults

On occasion, it may be necessary to default the main control

panel or one of the connected modules: the LINKS2X50 Radio

interface, the PC5132 wireless receiver, and the PC5400

Printer module.

To default the main control panel (hardware), perform the fol-

lowing:

1. Remove AC and battery from the panel.

2. Remove all wires from the Zone 1 and PGM1 terminals.

3. With a piece of wire short the Zone 1 terminal to the PGM1

terminal.

4. Apply AC power to the main panel.

5. When Zone Light 1 is lit on the keypad the default is com-

plete.

6. Remove AC power from the control

7. Reconnect all original wiring and power up the control.

NOTE: AC power must be used to power the panel. The panel

will not default if only the battery is used.

To default the main control panel software and other modules,

perform the following:

1. Enter the Installer’s Programming mode.

2. Enter the appropriate programming section [XXX].

3. Enter the Installer’s Code.

4. Re-enter the appropriate programming section [XXX].

The panel will take a few seconds to perform the default.

When the keypad is again operational the default is complete.

NOTE: If using Identified Wireless Keys (PC5132 v3.0 or later

only), when the main panel is defaulted, all wireless key

access codes must be re-programmed. Refer to your PC5132

v3.0 Installation Manual for more information.

Restore Alternative Communicator

(LINKS2X50)

to Default Programming. . . . . . . . . . . . . . . . . . . Section [993]

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 55 56

Komentáře k této Příručce

Žádné komentáře

DSC Power432 PC585 Instalační manuál Strana 30

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC Power432 PC585