DSC PC560 Manuál s instrukcemi stáhnout pdf (Strana 7)

Bypassing Zones

A “bypassed” zone will not cause an alarm. Zones may be bypassed to allow access to part of the

protected area while other zones are armed. For example, you could bypass the zone protecting your living

room. This would allow you to remain in the room, while the other zones on your system are armed.

With the system disarmed, enter [

∗

][1][Access Code] to display bypassed zones. The zone lights

representing bypassed zones will come ON. Ensure that any zone displayed as being bypassed is

intentionally bypassed. Zone bypasses are automatically cancelled when the panel is disarmed.

To Bypass Zones:

Enter [

∗

][1][Access Code]; the System light will flash.

Enter the number of the zone to be bypassed; the corresponding zone light will come ON to indicate that

the zone is bypassed. To remove a bypass, enter the zone number to shut its zone light OFF. When all

desired zones are bypassed, press the [#] key to return to “Ready”.

When you arm your system, the zones you have indicated will now be bypassed. When arming the system

with bypassed zones, it is always a good idea to enter the [

∗

][1][Access Code] command to review the list

of bypassed zones before entering an access code to arm the system. After ensuring that the desired

zones are bypassed, press the [#] key, and then enter an access code to arm the system.

Keypad Alarms

Three types of alarms may be activated by pressing and holding a single key on the keypad. Your

installer will inform you of how the [F], [A] and [P] keys will operate on your system.

[F] Press and hold the [F] key for 2 seconds to sound an [F] key alarm; the siren will sound with

a pulsed tone. The keypad will sound a series of short beeps once the system has accepted

the alarm.

[A] Press and hold the [A] key for 2 seconds to generate an [A] key alarm. The siren will not

sound when this function is activated. Your installer will inform you of how this alarm will

operate; this alarm may be programmed to activate a device, such as a door lock or a

warning light. The keypad will sound a series of short beeps once the system has accepted

the alarm.

[P] Press and hold the [P] key for 2 seconds to generate a [P] key alarm. The alarm may be

programmed as either silent or audible; your installer will inform you of how this al arm will

operate. If your installer has programmed this alarm to be audible, the keypad will sound a

series of short beeps once the system has accepted the alarm, and the siren will sound a

steady tone.

SL-40 KEYPAD

Zone Lights 1 to 4 indicate zone activity. When

a zone is secure, its zone light will be OFF;

when a zone is open, its zone light will be ON. If

a zone goes into alarm when the system is

armed, the alarm will be indicated on the zone

lights until the system is disarmed.

The “Ready” light will come ON when the system

is ready to be armed. When the “Ready” light is

OFF, there is an open zone on the system. The

zone must be closed or bypassed before the

system can be armed.

The “Armed” light will come ON to indicate that

the system is armed. The “Armed” light will flash

to indicate that the system is armed and that there

is no entry delay on any of the zones.

The “System” light will come ON to indicate:

•that zones are bypassed

•there is a trouble condition on the system

•there are alarms in memory.

Use the [

∗

][1][Access Code] command to

display the zones that have been bypassed; be

sure that zones are intentionally bypassed

before arming the system.

Use the [

∗

][2] command to display any trouble

conditions; be sure to have trouble conditions

corrected by your installer as soon as possible.

Use the [

∗

][3] command to view the alarms in

memory.

Important:

Follow the instructions in the manual to test your system weekly. Follow the

guidelines for correcting system trouble conditions; have any system trouble

conditions you cannot correct yourself attended to by your installer.

Press [#]:

•when an error is made in entering an access code, then enter the code again

•to return to “Ready” after using [

∗

] commands

[F] Key: Press and hold this key for 2 seconds to sound an [F] key alarm

[A] Key: Press and hold this key for 2 seconds to generate an [A] key alarm

[P] Key: Press and hold this key for 2 seconds to generate a [P] key alarm.

These keys must be enabled by your installer before they become functional.

Your installer will tell you how these keys operate on your system.

1 2 3 4

Ready Armed System

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Komentáře k této Příručce

Žádné komentáře

DSC PC560 Manuál s instrukcemi Strana 7

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC PC560