DSC MAXSYS PC4010 Instalační manuál stáhnout pdf (Strana 34)

TLM and Alarm (14)

The output will activate when a telephone line trouble is

present and an alarm occurs on any of the selected parti-

tions.

Failure To Communicate (15)

The output will activate when a Failure to Communicate

trouble is present. The output will stay activated until a

successful communication is sent to the central station.

Communications Active (16)

The output will activate while the panel is attempting to

communicate with the central station.

Ground Start (17)

The output will activate for a programmable number of

seconds before the panel attempts to communicate with

the central station.

NOTE: This output will follow the “Ground Start” PGM

pulse time (see Section 11.3 “PGM Output Pulse Times”).

This output shall not be used on UL listed systems.

Kissoff Output (18)

The output will activate for a programmed number of

seconds after a successful communication to the central

station.

NOTE: This output will follow the “Kissoff Pulse” PGM

pulse time (see Section 11.3 “PGM Output Pulse Times”).

Combus Power (19)

This output will deactivate when a Combus reset is per-

formed by the panel.

Ready Status (20)

The output will activate when all the selected partitions

are ready to be armed. If any of the selected partitions are

not ready, the output will deactivate.

Zone Alarm (21)

This output will annunciate when a selected zone has

gone into alarm. Any zone can be selected. If the zone

goes into alarm, the output will activate. The output will

remain active until the partition is armed again.

Zone Follow (22)

This output will follow a selected zone. Any zone can be

selected. If the zone is opened, tampered, or faulted, the

output will activate. When the zone is secured, the output

will deactivate. If the Follows + Alarms system toggle

option is enabled, when the zone goes into alarm the output

will remain active until the partition that the zone belongs

to is armed or disarmed (ref #[000200]).

Duress (23)

This output will activate when a Duress code is used to

perform any function.

NOTE: This output will follow the Duress pulse timer

(see Section 11.3 “PGM Output Pulse Times”).

Buzzer Follow (24)

This output will activate when any of the following

occur on the selected partitions: an entry delay, an auto-

arm pre-alert, or a 24HR Buzzer zone alarm.

Remote Operation (25)

This option can be activated remotely using download-

ing, and will remain active until deactivated by the

downloading computer.

Exit Follow (26)

This option will follow the exit delay for the selected par-

tition(s).

Entry Follow (27)

This output will follow the entry delay for the selected

partition(s).

Zone Tamper (28)

This output will activate when any zone tamper alarm

occurs on the selected partitions. It will remain active

until the partition is disarmed (alarm silenced) or the bell

time-out is reached.

Zone Fault (29)

This output will activate when any zone fault alarm

occurs on the selected partitions. It will remain active

until the partition is disarmed (alarm silenced) or the bell

time-out is reached.

Zone Tamper Follow (30)

This output will indicate when a zone goes into a tamper

alarm. Any zone can be selected. If the zone is tampered,

the output will activate; when the zone is restored, the

output will deactivate. When the Follows + Alarms sys-

tem toggle option is enabled, the output will remain

active until the partition that the zone belongs to is

armed (ref #[000200]).

Zone Fault Follow (31)

This output will indicate when a zone goes into a fault

alarm. Any zone can be selected. If the zone is faulted, the

output will activate; when the zone is restored, the output

will deactivate. When the Follows + Alarms system toggle

option is enabled, the output will remain active until the

partition that the zone belongs to is armed (ref #[000200]).

Armed Stay Mode (32)

This output will activate when a selected partition is

armed in the Stay mode (i.e. when the partition is armed

with Stay/Away zones bypassed).

Armed Away Mode (33)

This output will activate when a selected partition is

armed in the Away mode (i.e. when all Stay/Away zones

are active).

2-wire Smoke Alarm (34)

The output will follow the alarm status on the PC4701 2-

wire smoke input, if installed. If the input is in alarm, the

output will activate; when the alarm is restored, the out-

put will deactivate.

2-wire Smoke Trouble (35)

The output will follow the trouble status on the PC4701

2-wire smoke input, if installed. If the input exhibits a

trouble, the output will activate; when the trouble is

restored, the output will deactivate.

Waterflow Alarm (36)

The output will follow the alarm status on the PC4701

Waterflow input, if installed. If the input is in alarm, the

output will activate; when the alarm is restored, the out-

put will deactivate.

Waterflow Trouble (37)

The output will follow the trouble status on the PC4701

Waterflow input, if installed. If the input exhibits a trou-

ble, the output will activate; when the trouble is restored,

the output will deactivate.

Command Outputs 1-8 (38-45)

The output will activate when the corresponding [*] [7]

[1-8] command is entered on the selected partition. Enter

a pulse time for each output (default = 000 seconds; 005

seconds for Command Output #2). A pulse time of [000]

will allow the output to be toggled on and off using the

corresponding [*] [7] [1-8] command.

NOTE: All command outputs will deactivate when you

exit installer’s mode.

HINT: If you program more than one PGM for the same

command output (eg. command output 1), make sure

that either:

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 51 52

Komentáře k této Příručce

Žádné komentáře

DSC MAXSYS PC4010 Instalační manuál Strana 34

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC MAXSYS PC4010