DSC Envoy NT9010 Instalační příručka Strana 53
- Strana / 68
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Section 2.3: Changing Other NT9010 Functions
49
Zone Restorals
If the Restoral on Bell Time-out option is selected, the system will send the Zone
Restoral Reporting Code for the zone if the bell cut-off time has expired and the
zone is secured. If the zone is not secured when the bell cut-off time expires, the
system will send the restoral immediately once the zone is secured, or when the
system is disarmed. If the Restoral on Bell Time-out option is not selected, the
system will immediately send the Zone Restoral Reporting Code when the zone is
secured, regardless of whether or not the alarm output is active.
NOTE:
24 Hour type zones will report the restoral immediately when the
zone is secured.
Restoral on Bell Time-out. . . . . . . . . . . . . . . . . . . . . . . . . Section [380], Option [2]
AC Failure Communication Delay Time . . . . . . . . . . . . . . . . . . . . . . . Section [370]
2.3.13 Talk/Listen-in
Programming
NOTE:
The Event Buffer follows Swinger Shutdown option must be
enabled if Talk/Listen-In is used.
The NT9010 system has a Talk/Listen-In feature. This feature allows central station
operators to listen in on what is happening on the premises, and for some events
to talk to anybody present on the premises. You can program Talk/Listen-in sessions
to be triggered by zone alarms, keypad-activated Auxiliary and Panic alarms, open-
ings/closings, duress alarms, tamper alarms, or opening after alarm conditions.
For this feature to work, communications must be enabled (section [380], option
[1]), and the system must be programmed to report the event. For example, if a
reporting code for a zone is not programmed, an event in that zone will not initiate
Talk/Listen-In session. See 2.3.12 CommunicatorReporting Codes on page 47.
You can allow or disallow talk/listen-in sessions on telephone lines 1 and 3 by
changing the Talk/Listen on Phone Lines 1/3 option. You can allow or disallow
talk/listen-in sessions on telephone line 2 by changing the Talk/Listen on Phone
Line 2 option.
Zone Options
For the feature to work on a zone alarm, you must do the following:
• enroll the zone on the NT9010 (see Chapter 1: Quick Set Up on page 1)
• enable the talk/listen-in feature on the zone (section [802], sub-sections [50] to
[53])
• program a reporting code for each zone alarm
You can have the talk/listen-in session take place on either the NT9010 control unit
or the remote sounder (if installed). In the Port Assignments sections (section
[802], sub-sections [10] to [13]), choose the unit that is closest to the zone. If you
do not assign one of the units, the talk/listen-in session will not take place over
both units.
NOTE:
All zones programmed as silent will not initiate a Talk/Listen-In
session. Only a Listen-In session can occur.
- Installation 1
- Limited Warranty 2
- Table of Contents 3
- WARNING Please Read Carefully 4
- 1.1.3 Main system 6
- Specifications 6
- 1.1.4 Additional 7
- 1.1.5 Peel-off 8
- Instruction 8
- 1.2.5 Connecting 10
- Chapter 1: Quick Set Up 12
- Section 1.3: Troubleshooting 18
- 2.1.6 Reviewing 22
- Programming 22
- 2.1.7 Exiting 22
- Works For Users 23
- 2.2.2 Access Codes 24
- 2.2.3 Voice Prompt 26
- Interface 26
- 2.2.4 Alarm 27
- Announce 27
- 2.2.5 Arming and 28
- Disarming 28
- 2.2.8 Bell Options 30
- 2.2.9 User 31
- Commands 31
- 2.2.10 Function 35
- 2.2.13 Keypad 38
- 2.2.14 Sleep Mode 39
- 2.3.1 Zone 40
- Definitions 40
- 2.3.13 Talk/Listen-in 53
- 2.3.14 Downloading 55
- 2.3.21 Installer 59
- 2.3.22 Walk Test 60
- Appendix A: Guidelines for 61
- Locating Smoke Detectors 61
- Appendix B: Reporting Codes 62
- Zone Alarm/Restoral Codes 64
- WARNING!: 65
- WLS904P-433 with 66
- Three-Pin Jumper 66
- TOP VIEWSIDE VIEW 67
- Detection Pattern 67
- FCC COMPLIANCE STATEMENT 68
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC Envoy NT9010
(36 stránky)
(16 stránky)Cables Direct B5-100Y manuels
Manuels d'utilisation et guides de l'utilisateur pour Câbles de mise en réseau Cables Direct B5-100Y.
Nous fournissons des manuels en pdf 1 Cables Direct B5-100Y à télécharger gratuitement par type de document : Fiche technique
Komentáře k této Příručce