DSC PC580 - V2.3 Instalační manuál stáhnout pdf

If you are intending to use DLS-3 software with this product, a new DLS-3 driver must be

downloaded from the DSC web site at http://www.dscsec.com/dls3drivers.htm. Install

this driver on your computer in the same directory as your DLS-3 software.

W A R N I N G

This manual contains information on limitations regarding

product use and function and information on the limitations as

to liability of the manufacturer.

Section 1: IntroductionSection 1: Introduction

Section 1: Introduction

This manual describes how to install, program and maintain the PC5102-433. Before you

install the PC5102-433 module, you should complete the following steps in your system

installation:

1. Plan the installation and wiring of the security system (see your system

Installation Manual

2. Install the control panel, and install and enroll at least one keypad to use for programming.

Program the PC5102-433 from a system keypad or using DLS-3 v1.3 with the PC5102-433

v1.0 Driver Pack. Read your system

Installation Manual

for more information.

1.1 How to Use this Manual

Read this manual before you begin installing the PC5102-433. To install and set up the

PC5102-433 and wireless keys, follow these steps. Refer to the sections listed below.

1. Temporarily mount and wire the PC5102-433 module (see

Section 2

2. Enroll and program wireless keys (see

Section 3

3. Complete PGM and other programming on the system (see

Section 4

4. Test the placement of all the wireless keys

(see Section 5).

5. Permanently mount the PC5102-433 receiver

(see Section 5).

For additional information on trouble conditions and battery replacement, see

Section 6.

For help with troubleshooting, see

Section 7.

1.2 Specifications and Features

• Current Draw: 50mA (standby) 200mA maximum (both outputs active)

• Frequency: 433 MHz

• Receiver can receive signals from up to 8 wireless keys

• Antenna - internal. Installation not required

• Location

- can be wired up to 750 ft/230m. from the main panel with 22 gauge wire

- connects to Keybus

- for longer wire runs, thicker gauge wire must be used

• Compatibility: The PC5102-433 v1.X can be connected to the following panels:

PC501X, P832/DL, PC5020, P-8+, PC1555, P-6B, PC1555MX, P-6BMX, PC580, P-48

1.3 Compatible Wireless Keys

Please refer to the instruction sheets of the following keys for more information.

The PC5102-433 v1.X can receive signals from the following keys:

• WLS909-433 Wireless Key • WLS919-433 Wireless Key

• PWLS909-433 Wireless Key • PWLS919-433 Wireless Key

PC51O2-433NA v1.0 Installation Manual

1 2 3 4 5 6 ... 11 12

Shrnutí obsahu

Strany 1 - Section 1: Introduction

If you are intending to use DLS-3 software with this product, a new DLS-3 driver must bedownloaded from the DSC web site at http://www.dscsec.com/dls3

Strany 2 - 2.2 Terminal Descriptions

P R O G R A M M I N G W O R K S H E E T SPC5102 Output OptionsEntry Description00 Null (No Operation)01 Main Panel PGM102 Main Panel PGM203 PC5208 PG

Strany 3 - Powerflash

WARNING Please Read CarefullyNote to InstallersThis warning contains vital information. As the only individual in contact withsystem users, it is your

Strany 4 - 3.3 Identified Wireless Keys

LIMITED WARRANTYDigital Security Controls Ltd. warrants the original pur-chaser that for a period of twelve months from the dateof purchase, the produ

Strany 5 - Section 4: Other Programming

21.4 BatteriesThe PWLS909-433/WLS909-433 use three A-76 batteries and the PWLS919-433/WLS919-433 use two CR2032 lithium batteries.Section 2: PC5102-43

Strany 6 - 4.4 Deleting Wireless Keys

32.5 Connecting a Garage Door to the PC5102-433Connect an output of the PC5102-433 across thewall-mounted push button or directly at the motorof the g

Strany 7 - Section 6: Additional Notes

43.2 Enroll & Program Wireless KeysFor wireless keys to work on the system, you need to enroll them and then program the functionbuttons, if the d

Strany 8

5Opening/Closing By Wireless Key ReportingNOTENOTENOTENOTENOTE: The Identified Wireless Key Closing option is only available with the PC5020, P-8+, P

Strany 9

6The system will generate a General System Supervisory trouble if the module is removedfrom the Keybus. If you need to remove the PC5102-433 module fr

Strany 10 - Default = 01

7Testing Individual Wireless KeysTo ensure that the PC5102-433 receiver is receiving transmissions from these devices,use the function keys on the (P)

Strany 11 - WARNING Please Read Carefully

8Section 7: TroubleshootingSection 7: TroubleshootingSection 7: TroubleshootingSection 7: TroubleshootingSection 7: Troubleshooting1. When I enter Se

Strany 12 - LIMITED WARRANTY

9Wireless Key OptionsyrtnEyrtnEyrtnEyrtnEyrtnEnoitpircseDyeKnoitpircseDyeKnoitpircseDyeKnoitpircseDyeKnoitpircseDyeKyrtnEyrtnEyrtnEyrtnEyrtnEnoitpircs