DSC PC1404 v1.1 Uživatelský manuál stáhnout pdf (Strana 26)

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by

Digital Security Controls could void your authority to use this

equipment.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interfer-ence in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be deter-mined by turning the equipment

off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

- Re-orient the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or experienced radio/television technician for

help.

The user may find the following booklet prepared by the FCC useful:

"How to Identify and Resolve Radio/Television Interference Prob-

lems". This booklet is available from the U.S. Government Printing

Office, Washington D.C. 20402, Stock # 004-000-00345-4.

The keypads represented in this manual can be used with the follow-

ing Control Units: PC1616, PC1832, PC1864.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules and, if the

product was approved July 23, 2001 or later, the requirements adopt-

ed by the ACTA. On the side of this equipment is a label that con-

tains, among other information, a product identifier. If requested, this

number must be provided to the Telephone Company.

PC1404 Product Identifier US: F53AL01BPC1404

USOC Jack: RJ-31X

Telephone Connection Requirements

A plug and jack used to connect this equipment to the premises wir-

ing and telephone network must comply with the applicable FCC

Part 68 rules and requirements adopted by the ACTA. A compliant

telephone cord and modular plug is provided with this product. It is

designed to be connected to a compatible modular jack that is also

compliant. See installation instructions for details.

Ringer Equivalence Number (REN)

The REN is used to determine the number of devices that may be

connected to a telephone line. Excessive RENs on a telephone line

may result in the devices not ringing in response to an incoming call.

In most but not all areas, the sum of RENs should not exceed five

(5.0). To be certain of the number of devices that may be connected

to a line, as determined by the total RENs, contact the local Tele-

phone Company. For products approved after July 23, 2001, the

REN for this product is part of the product identifier that has the for-

mat US: AAAEQ##TXXXX. The digits represented by ## are the

REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier

products, the REN is separately shown on the label.

Incidence of Harm

If this equipment (PC1616, PC1832, PC1864) causes harm to the

telephone network, the telephone company will notify you in ad-

vance that temporary discontinuance of service may be required. But

if advance notice is not practical, the Telephone Company will notify

the customer as soon as possible. Also, you will be advised of your

right to file a complaint with the FCC if you believe it is necessary.

Changes in Telephone Company Equipment or Facilities

The Telephone Company may make changes in its facilities, equip-

ment, operations or procedures that could affect the operation of the

equipment. If this happens the Telephone Company will provide ad-

vance notice in order for you to make necessary modifications to

maintain uninterrupted service.

Equipment Maintenance Facility

If trouble is experienced with this equipment (PC1616, PC1832,

PC1864) for repair or warranty information, contact the facility indi-

cated below. If the equipment is causing harm to the telephone net-

work, the Telephone Company may request that you disconnect the

equipment until the problem is solved. This equipment is of a type

that is not intended to be repaired by the end user.

DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122

Additional Information

Connection to party line service is subject to state tariffs. Contact the

state public utility commission, public service commission or corpo-

ration commission for information.

Alarm dialing equipment must be able to seize the telephone line and

place a call in an emergency situation. It must be able to do this even

if other equipment (telephone, answering system, computer modem,

etc.) already has the telephone line in use. To do so, alarm dialing

equipment must be connected to a properly installed RJ-31X jack

that is electrically in series with and ahead of all other equipment at-

tached to the same telephone line. Proper installation is depicted in

the figure below. If you have any questions concerning these instruc-

tions, you should consult your telephone company or a qualified in-

staller about installing the RJ-31X jack and alarm dialing equipment

for you.

INDUSTRY CANADA STATEMENT

NOTICE: This Equipment meets the applicable Industry Canada Terminal

Equipment Technical Specifications. This is confirmed by the registration

number. The abbreviation, IC, before the registration number signifies that

registration was performed based on a Declaration of Conformity indicat-

ing that Industry Canada technical specifications were met. It does not im-

ply that Industry Canada approved the equipment

NOTICE: The Ringer Equivalence Number (REN) for this terminal equip-

ment is 0.1. The REN assigned to each terminal equipment provides an in-

dication of the maximum number of terminals allowed to be connected to

a telephone interface. The termination on an interface may consist of any

combination of devices subject only to the requirement that the sum of the

Ringer Equivalence Numbers of all devices does not exceed 5.

PC1404 Registration number IC: 160A-PC1404

1 2 ... 21 22 23 24 25 26 27 28

Komentáře k této Příručce

Žádné komentáře

DSC PC1404 v1.1 Uživatelský manuál Strana 26

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu DSC PC1404 v1.1