DSC PC1150 Instalační manuál

INSTALLATIONMANUALPC1150This device complies with Parts 15 and 68 of the FCC rules. Operation is subject to the following two conditions: (1)this devi

To display trouble conditions, enter [*][2]. Trouble conditions are represented with the following lights:LightZone 1Zone 2Zone 3Zone 4“Armed”Low Batt

f*]+fsl: User Programming CommandThe [*][5] programming command allows the user to program Access Codes. The first Access Code is theMaster Code and t

Setting the Clock[*]+[G]i[Mas terCode]+[ I]The System Clock uses a 24-hour clock format. For example, 8:05 AM would be entered as 0805; 1:30 PM would

Utility Output Command[*I+[71 or [*]+p]+[Access Code]The Programmable Output (PGM terminal) can be programmed to be activated by a keypad command. Thi

PROGRAMMING GUIDEWith the panel disarmed, enter [*][8][lnstaller’s Code]. The default installer’s Code is 1212. The Installer’sCode should be changed

Binary Data DisplayZone lights 1 through 4 are used to display the value of each digit of data in a binary format as shown here:ValueZone 1Zone 2Zone

PROGRAMMING SECTIONS[Of] 1st Phone NumberThis is the first telephone number the Communicator will dial; refer to Section [25] Communicator Call Direct

3/f format - Non-extencfed reportingRequires:l 3-digit account code in sections [02] or 1041. For example, enter 1230 for account code 123l Format Cod

[OS]Opening [Disamingj Reporting Codes /After Alarm Reporting CodeOpening Reporting Codes are transmitted to indicate disarming of the system by Acces

Zone Definitions Digit 2Digit 2 determines the zone type as described below:PIPIPI131r41PIPIPIStandard Delay: Entry and Exit Delays are normally used

NOTES FOR UL INSTALLATIONSThis equipment is UL listed in accordance with UL 1023 (Household Burglar Alarm System Units). Thisequipment has not been in

[12] 1st System Option CodeWhen Section [12] is entered, the 4 Zone Lights, “Ready” and “Armed” lights will indicate which options areenabled. If a li

1143 3rd System Option CodeRefer to Section [12] for programming information.LIGHT111ON =Access code required for bypassl OFF =Access code not require

El161“Slow” Zone Response Time (01 to 99 x IO ms) Location [5] determines the “slow” zone response time;this time is programmable from 10 ms to 990 ms

1231 Communication FormatsThis section determines the communication format to be used when transmitting information to the twotelephone numbers progra

Radionics FormatFor conventional Radionics 3/l format, the communications mode should be set on either Radionics rounds [B]or Radionics parity [Cl. Th

PIStrobe Output (Latched Alarm Output)WIThe PGM switches to ground on an alarm and remains low until the panel is disarmed. It can be usedto indicate

[30] Reset to Factory DefaultSoftware ResetEntering Section [30] will reset the control panel’s programming to the default settings. When Section [30]

1321 5th System Option CodeRefer to Section [12] for programming instructions.LIGHT[IION =. OFF =PION =. OFF =[31ON =. OFF =[41ON =l OFF =[RION =l OFF

PROGRAMMING WORKSHEETSNOTE: In sections [Ol] to [lo], do not enter data into sections that are not used.1st Phone NumberPage i4Enter [0] for the digit

Closing (Arming) Reporting Codes /Partial Closing Reporting CodePage f5IAccessCode1-AccessCode2-AccessCode3IAccessCode4l---L--AccessCode5/AccessCode6-

TABLE OF CONTENTSINTRODUCTIONFeatures...

Maintenance Alarms & RestoralsPage 16DefaultL!3JL_.-.lA3.AJu-l,F,8,,,E,3,-Azz.A_l-l.!z.d%-LEJ.J-Zone DefinitionsLow Battery AlarmAC Fail AlarmFuse

2nd System Option Code Page 18Default Zone Light ON,oFF, -Zone Light 1Zone 4 N.O. without EOL,oFF, -Zone Light 2Master Code not changeable,oFF, -Zone

System Times Page 79Defaultl.lL.!L-Entry Delay (seconds)t?!i_zJ-Exit Delay (seconds),0,4-Siren Cut-off (minutes)J.J_r&u/AC fail transmission delay

[23] Communication Formats Page 21Default&L l--J1st Telephone NumberL.BJ I2nd Telephone NumberA format for both numbers must be programmed, even i

Communicator Call Direction Options Page 23This section must be completely programmed; do not press [#] to exit until all entries are completed.Defaul

4th System Option CodeDefault,ON, /Zone Light 1Page 24Zone Light ONEnable download answer,oFF, IZone Light 2 Enable download callbackDisable callback,

LIMITED WARRANTYDigital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the productshall be free of defe

FCC COMPLIANCE STATEMENTThis equipment generates and uses radio frequency energy, and if not installed and used properly, in strict accordance withthe

PROGRAMMlNG SECTlONS[01]1st PhoneNumber...

INTRODUCTIONFEATURESKeypad ProgrammableThe PC1 150 comes complete with a default programso that it is operational straight from the box with aminimum

INSTALLATIONMounting the Pane/The keypad should be located close to the designated “Entry-Exit” door and be mounted at a height convenientfor all user

Burglary Zone WiringBurglary zone definition, (for example, Delay, Instant, 24-Hour, and so on) is programmed using the keypad.Refer to Programming Gu

KEYPAD FUNCTIONSIntroductionThe PC1 150 keypad provides complete control of the PC1 150 control panel. The panel can be completelyprogrammed from the

Arming Without Entry DelayTo eliminate the Entry Delay, arm the system by entering [*][9][any Access Code]. An exit through a DelayZone may be made as